600-910 Transfer Case Motor Compatible with Select Models

First off, the product quality seems good and it fixed my issue. 2005 suburban z71 with np8 transfer case and 4 button selector switch. My issue: service 4wd indicator and truck stuck in 4wd. Scan tool pulled c0321 code. Diagnosis: checked fuse (TREC) first. Then checked for corrosion/broken wires under fuse box in engine bay. Check for connections and corrosion behind knee plate under dash at TCCM. The TCCM is located on drivers side above emergency brake petal. Checked selector switch in dash with scan tool. Engaged/disengaged front axel with scan tool. Checked wiring/plug at encoder motor on t case. Verified 12v at the big orange wire in the connector. Then verified 5v at green wire. At this point I feel pretty confident it’s the encoder motor. Removal/Install: This is an easy job. Remove the skid plate below t case. Remove front driveshaft (it needs to go back the same way on the front diff so mark it before you take it apart). Unplug encoder motor. Remove the three bolts holding it on. Pull it out. IMPORTANT: The new encoder motor comes in the neutral position. The shaft on the t case has a key way on it. That key way needs to be facing straight down towards the ground which will put the t case in neutral. You need to put the vehicle transmission in neutral in order to turn the shaft on the t case!! Use wheel chocks please!! Once the transmission is in neutral, grab the shaft carefully with a pair of pliers and turn it so that the key way is facing down. Now you can install the encoder motor. Make sure you clean/reuse the gasket or, preferably, get a new gasket. There is a specific order to tighten/torque the bolts. Just google it. Clean/Reinstall everything else. Potential Problem: Here is what I wrote this review for bc I couldn’t find any information for the problem I encountered. When I turned my truck on, the lights on my selector switch flashed and then they all turned off and the t case wouldn’t respond. I scanned and pulled like 6 codes for the t case! Here is what I did. Check the plug to make sure it’s connected. Take both battery cables off the battery and touch them together for a few minutes. Reinstall and try again. I think the TCCM has to reset. Fired the truck back up, neutral light was illuminated on the switch and it shifted into all selections flawlessly. Hope this helps someone!

Fits like and works like OEM

Complete Chinese junk, don’t even waste your time. There is no quality control with these. I spent a little more money with Dorman hoping it might work. Thank God Amazon is easy to return but only within 30 days. I took a gamble and I knew it was a gamble. This is definitely not OEM General Motors original quality. I installed it and it does switch between 2 high 4high 4 low, but these have a motor lock that is supposed to hold the transfer case clutch pack to lock it in four-wheel-drive. The motor lock function does not hold. You think you are in four-wheel-drive but you’re not. I took the Dorman apart and the components are much weaker and thinner. I was hoping to mix and match parts with my original and the doormat parts are different. I ended up returning it and ordering One from a junkyard off eBay. I would rather have a 25-year-old used wrecking yard part, I am going to use two actuators to make one good one. FYI, I already had to make my own aluminum clutch locking disc for the motor lock because the factory original is plastic and it broken half. Unfortunately, these NP8 transfer cases aren’t the best and these actuators are a major problem. I wish there was a good remanufacturing company that rebuilds originals and supplied these on Amazon. But Amazon is just flooded with Chinese parts, so buyer beware and the worst part is AC Delco is discontinued. It looks like we are on our own with these, we need to bring back American quality and engineering, this is definitely a case of you get what you pay for. There is good China and there is bad China, this is definitely bad China disguised in a Dorman box. .

I had been getting a Service 4wd alert on my 2005 Sierra Z71. I replaced the switch first, but that didn’t fix it. I tried to find the GM motor, but it seems that has been discontinued, which is surprising considering the number of vehicles that use this part. So I bought the Dorman. Side by side comparison, it seems pretty similar to the OEM part. I reused the gasket from the original after cleaning with brake cleaner, and I swapped the alignment bushing from the original using needle nose pliers. I have never done this job before, but it is not too difficult. I did it without completely removing the front drive shaft. I removed the retainers from the front end of the drive shaft so I could slide the shaft back and out of the yoke. This gave me enough room to get the middle bolt out of the old motor. The other two bolts came out with an impact. There are instructions and warnings on the new part to ensure that you don’t move the position of the motor by hand. If you can, you are supposed to put the transfer case in N by pressing the 2hi and 4lo buttons. Mine moved to N (I thought), but when I tried to put the new motor in, it wouldn’t align with the shaft on the transfer case. I grabbed the shaft with my fingers and turned it and it rotated a bit more and then had a very noticeable click as it found the actual neutral. Then the new motor went right in. I suspect this was the problem with my truck, it wasn’t fully in the position the motor thought it was in. Start to finish was probably about an hour, though I suspect it could be done faster now that I have an idea what I am doing. Hopefully this part will last and I won’t need to do it again.

Fast shipping. Perfect fit works great.

El articulo corresponde a la descripción, Nuevo y al ser un producto dorman espero sea mejor calidad que los que son mas económicos. Me llegó el día de hoy (antes de lo esperado) y hoy mismo lo instale trabaja correctamente sin problemas. Corrigió la falla de mi Silverado 2005. NOTA: Viene en la posición Neutral, hay que poner el engrane del transfer en esa misma posición para poder instalarlo. ACTUALIZACIÓN: FUNCIONÓ SOLO 10 MESES, CURIOSAMENTE DAN SOLO 6 MESES DE GARANTÍA.

Reçu dans le délais de 2 jours et fonctionne très bien. Bon vendeur je recommande. a+++++

Fit perfect half price of on from Napa been on for 2 months now works great

They sent the motor and it's not working